MORITO_vol01
32/132

①②③④⑤①②③────○○○─○○○○───PRESSFASTENERS受注生産品Produced on orderサイズ・構造について●規格サイズをご指定ください。●ホック頭のタイプをご確認ください。●サイズによって構造が異なります。●素材によって仕上がりサイズに多少の誤差が生じます。●18㎜以上の釦は検針感度をご確認ください。打ち付け加工について●サイズ別に樹脂の下駒をご用意しています。●サンプル時点での打ちテストと本生産前にも打ちテストをお願いします。●製品に打ち付けの際は、穴を開けてからの加工をおすすめします。●打ち付けた際に回る場合や打痕が出る場合があります。Size Variation 規格サイズUnder 3parts アンダーパーツ(3つ組)5BX(▶P.016)6BX(▶P.016)7401(▶P.017)7301(▶P.017)Flat Type フラットタイプ10㎜25㎜FW-1515.0㎜FW-1818.0㎜12㎜15㎜30㎜FW-2121.0㎜4301(▶P.017)7101(▶P.021)About materials provided ●Please send materials in an unprocessed state (not layered, Size and structure ●Please confirm the features, size. ●Make sure to confirm the type of cap.●Depending on the size, the structure is different.●Depending on the material, there may be slight variations in About pressing ●Resin lower dies are available for each size. ●Snap fasteners are press-tested at the sample stage, and we ●Material thickness, elasticity, and hardness can be adjusted glue resist dyed, etc.).by backing and layering.●If the adjustment is difficult, in some cases wrap processing is not possible.●Pleasebe sure to label the material front and back, the color number, etc.the finished size.●Please use needle detector and check the sensitivity of the buttons which are more than 18mm.ask that you press-test them before full-sclae production.● When attaching it to the product, it is recommended that you open up a hole before processing.● In some cases, dents may occur or the snap fastener easliy turns around when using press to attach.TH982(▶P.024)18㎜35㎜FW-2323.0㎜21㎜FW-2525.0㎜規格サイズ一覧 Size variation10㎜12㎜15㎜18㎜21㎜23㎜25㎜30㎜①素材 Material②キャップ Cap③ホック Hook※10㎜にはクッション材は入りません。※For the size of 10mm, cushion material is not put in.23㎜40㎜FW-3030.0㎜ ○※①素材 Material②キャップ(アルミ) Cap(Aluminum)③クッション材 Cushion④ホック(真鍮) Hook(Brass)⑤座金(アルミ) Washer(Aluminum)ラップホックCaution 注意事項支給していただく素材について●素材は加工(糊引き、漉きなど)されていない状態でお送りください。●素材の厚み、伸縮性、硬さを裏張りやスキ加工によって調整します。●調整が困難な場合はクルミ加工ができないこともあります。●素材には必ず、表裏、色番などの表記をお願いします。03103WRAP SNAP

元のページ  ../index.html#32

このブックを見る